[JG939A] ราคา ขาย จำหน่าย HPE 5130 48G 2SFP+ 2XGT EI Switch

Product overview

The HPE FlexNetwork 5130 EI Switch Series comprises Gigabit Ethernet switches that support static and RIP Layer 3 routing, diversified services, and IPv6 forwarding, as well as provides four 10-Gigabit Ethernet (10GbE) interfaces. Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in small data centers. High availability, simplified management, and comprehensive security control policies are among the key features that distinguish this series.

Features and benefits

Software-defined networking

• OpenFlow

Supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control (routing decision) paths

Quality of service (QoS)

• Broadcast control

Allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic

• Advanced classifier-based QoS

Classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a port, VLAN, or whole switch

• Powerful QoS feature

Supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR

• Traffic policing

Supports Committed Access Rate (CAR) and line rate

Connectivity

• Auto-MDIX

Adjusts automatically for straight-through or crossover cables on all 10/100/1000 ports

• Flow control

Provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations

• High-density connectivity

Provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Layer 3 switch

• IEEE 802.3at Power over Ethernet (PoE+) support

Simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in supplying local power at each access point location

• Ethernet operations, administration, and maintenance (OAM)

Detects data link layer problems that occurred in the “last mile” using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices

Performance

• Non-blocking architecture

Up to 176 Gbps non-blocking switching fabric provides wire-speed switching with up to 130.9 million pps throughput

• Hardware-based wire-speed access control lists (ACLs)

Helps provide high levels of security and ease of administration without impacting network performance with a feature-rich TCAM-based ACL implementation

Specifications

I/O ports and slots

• 48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/ 100BASE-TX: half or full; 1000BASE-T: full only

• 2 SFP+ fixed 1000/10000 SFP+ ports

• 2 RJ-45 1/10GBASE-T ports

Additional ports and slots

• 1 RJ-45 serial console port

Physical characteristics

• Dimensions : 17.32(w) x 10.63(d) x 1.72(h) in. (44 x 27 x 4.37 cm) (1U height)

• Weight : 11.02 lb (5 kg)

Performance

• 1000 Mb Latency : < 5 µs

• 10 Gbps Latency : < 3 µs

• Throughput : up to 130.9 Mpps

• Routing/Switching capacity : 176 Gbps

• Routing table size : 512 entries (IPv4), 256 entries (IPv6)

• MAC address table size : 16384 entries IPv6 Ready Certified

Electrical characteristics

• Frequency : 50/60 Hz

• Maximum heat dissipation : 122/184 BTU/hr (128.71/194.12 kJ/hr), for AC power. For DC power min heat dissipation is 122 BTU/hr and 184 BTU/hr max.

• AC Voltage : 100–240 VAC, rated (depending on power supply chosen)

• DC Voltage : -48 to -60 VDC

• Current : 2 A

• Maximum power rating : 54 W

• Idle Powe : 36 W